John

Members
  • Content count

    12
  • Joined

  • Last visited

    Never

Community Reputation

0 Neutral

About John

  • Rank
    Member

Profile Information

  • Gender
    Not Telling
  1. John

    Building Zpuino for Arcade MegaWing

    How about Saturday? Sometime midday to midnight Central European Time. /John
  2. John

    Building Zpuino for Arcade MegaWing

    Which ISE version are you guys using?I'm using ISE 13.4 Perhaps the prom-generic-dp-32.vhd file is the catch? I can build the bit file when the pre-built prom-generic file is available, but after a make clean command make will report: make[1]: zpu-elf-g++: Command not found What is zpu-elf-g++ and where do I find it? Also is there a reason for not having a xise file in the variant directories? How am I supposed to switch between the variants?
  3. John

    Building Zpuino for Arcade MegaWing

    Today I downloaded and built from alvieboy-ZPUino-HDL-fb9841b.zip, but the result is the same as previously. Power cycling does not help. Trying to attach the bit file. papilio_one_routed.bit.txt
  4. John

    Building Zpuino for Arcade MegaWing

    Yes, I have the smalfs directory in place. Arduino output using my bit file SmallFS: Packed 5 files sucessfully zetris.cpp: In function `void area_init()': zetris.cpp:313: warning: unused variable 'x' zetris.cpp:313: warning: unused variable 'y' Binary sketch size: 6912 bytes (of a 12160 byte maximum) Appending extra data file Board: GadgetFactory Papilio One 500 w/ 8-bit HQVGA @ 96000000 Hz (0xa4010e01) Programming completed successfully in 31.13 seconds. Using the prebuilt zpuino-ZB2-PapilioOne-S3E500-HQVGA-8bit-ArcadeWing.bit SmallFS: Packed 5 files sucessfully zetris.cpp: In function `void area_init()': zetris.cpp:313: warning: unused variable 'x' zetris.cpp:313: warning: unused variable 'y' Binary sketch size: 6912 bytes (of a 12160 byte maximum) Appending extra data file Board: GadgetFactory Papilio One 500 w/ 8-bit HQVGA @ 96000000 Hz (0xa4010e01) Programming completed successfully in 31.14 seconds.
  5. John

    Building Zpuino for Arcade MegaWing

    I built Hyperion with Apollo ucf. I will get the Zetris sketch to load and the blocks can be controlled, but background is black, there is no sound and the score board is a solid yellow rectangle. /John
  6. John

    Building Zpuino for Arcade MegaWing

    Hyperion will not build. There is no ucf file. Ok to borrow from ucf from Apollo? /John
  7. John

    Building Zpuino for Arcade MegaWing

    With zpuino-ZB2-PapilioOne-S3E500-HQVGA-8bit-ArcadeWing.bit configured in the FPGA, Arduino tool will only upload the sketch when board with 8-bit HQVGA is selected. When I configure the FPGA with the bit file I built my self. Only the board setting without 8-bit HQVGA will load, as you suggested. But sketch does not work! Also, my bit file will give a "No signal" on my monitor. I can see the delta sigma coder(sound device) in ISE project but can't find any graphic generator. I'm pretty sure this version does not contain video output.
  8. How do build the Zpuino in a version for the Arcade Wing? I intend to modify it before running Zetris. Is one of the variants suitable? When building the alvieboy-ZPUino-HDL-3e2595b\zpu\hdl\zpuino\boards\papilio_one\s3e500\ise version and trying to upload Zetris from Arduino I get: Board: GadgetFactory Papilio One 500 @ 96000000 Hz (0xa4010f00) Board mismatch!!!. Board is: 0xa4010f00 'GadgetFactory Papilio One 500' Sketch is for: 0xa4010e01 'GadgetFactory Papilio One 500 w/ 8-bit HQVGA'
  9. John

    Zetris upload problem

    Hello Jack, I just run the Test plan. The output is pasted below. Afterwards I loaded the file Quickstart-Papilio_One_500K-v1.5.bit to test the serial port and the ASCII chart is flowing just fine on COM5:9600baud. Also measured the voltages next to B(0-3): 2V5-2.50V 3V5-3.30V 5V-4.86V /John ################################################################# Programming Arcade MegaWing Verification to Papilio Using devlist.txt Programming a Papilio One 500K Using devlist.txt JTAG chainpos: 0 Device IDCODE = 0x41c22093 Desc: XC3S500E Uploading "bscan_spi_xc3s500e.bit". Done. Programming time 224.0 ms Programming External Flash Memory with "zpuino-ZB2-PapilioOne-S3E500-HQVGA-8bit-ArcadeWing.bit". Found SST Flash (Pages=2048, Page Size=264 bytes, 4325376 bits). Erasing : Ok Verifying : ..Pass Programming : ..............Finished Programming Ok Verifying : ..Pass Done. SPI execution time 8016.0 ms USB transactions: Write 3849 read 3133 retries 0 Using devlist.txt JTAG chainpos: 0 Device IDCODE = 0x41c22093 Desc: XC3S500E ISC_Done = 0 ISC_Enabled = 0 House Cleaning = 1 DONE = 0 Cannot get programmer version, aborting Press any key to continue . . . #################################################################
  10. John

    Zetris upload problem

    When connecting the USB cable, Arduino finds two new com ports, COM4 and COM5. Device manager reports COM5: "on USB Serial Converter B" Tried both and they produce the same message as previously posted. I'm running Windows7. /John
  11. John

    Zetris upload problem

    Actually I did load that bit file and the monitor reports a 800x600 signal, so the ZPU seems to be running. /John
  12. John

    Zetris upload problem

    Hi, I'm trying to upload Zetris on my Papilio One (500) with an Arcade Mega Wing, following the Papilio_Arcade_User_Guide.pdf, but ZPUino IDE fails as reported below. SmallFS: Packed 5 files sucessfully zetris.cpp: In function `void area_init()': zetris.cpp:313: warning: unused variable 'x' zetris.cpp:313: warning: unused variable 'y' Binary sketch size: 6912 bytes (of a 12160 byte maximum) Appending extra data file Cannot get programmer version, aborting. Both COM ports gives the same messages. Pong demo works loaded to FPGA and to FLASH so the HW seems to be ok. What shall I do to fix this problem? /John