pirx Posted October 25, 2013 Report Share Posted October 25, 2013 Hi, I've been developing Papilio apps on my Macbook Pro. It has beenworking great so far. Normally, I run ubuntu under vmware and downloadbit files using papilio-prog. Yesterday, I upgraded to Maverick. Unfortunately, now I can't seem to get papilio-prog to work. If I run itI get the following error. % papilio-prog -cCould not access USB device 0403:6010. I recompiled the source, and I get basically the same message. I alsotried it using sudo. I looked at /dev and now I get the following devices. cu.usbserial-00001014Bcu.usbserial-141Atty.usbserial-00001014Btty.usbserial-141A I think this has changed, but I can't remember what it used to show. Any suggestions? Link to comment Share on other sites More sharing options...
Jack Gassett Posted October 25, 2013 Report Share Posted October 25, 2013 Oh boy, I just released an installer and tutorial for Mac OSX, and now its not working for Maverick... Can you give the installer a try and see if maybe it does work under Maverick?http://gadgetfactory.net/learn/2013/10/25/install-papilio-loader-on-mac-osx/ Jack. Link to comment Share on other sites More sharing options...
pirx Posted October 25, 2013 Author Report Share Posted October 25, 2013 I downloaded the Mac Installer. Installation worked fine. But the programmer still can't access the device. Here is the message I get. Could not access USB device 0403:6010. If this is linux then use sudo. I tried it from the GUI and from the command line. On the command line, I triedit with sudo. None of these attempts worked. Pat Link to comment Share on other sites More sharing options...
Jack Gassett Posted October 25, 2013 Report Share Posted October 25, 2013 Do you have any other FTDI devices you can test? Is it a FTDI driver problem or a FT2232 problem? Jack. Link to comment Share on other sites More sharing options...
pirx Posted October 25, 2013 Author Report Share Posted October 25, 2013 Good idea. I tried my Arduino and that worked. It uses an FTDI chip, but probablya different ftdi driver stack. Pat Link to comment Share on other sites More sharing options...
Jack Gassett Posted October 25, 2013 Report Share Posted October 25, 2013 Well, that is a good piece of the puzzle... It brings up another question though, are the virtual COM ports of the Papilio working? Can you load a bit file that outputs something over the serial port and see the output? This may be a catch 22 for you though. Jack. Link to comment Share on other sites More sharing options...
pirx Posted October 26, 2013 Author Report Share Posted October 26, 2013 I'm away from my mac the next couple of days. I will look into that when I get back. Although,as you say, it may be tricky to do without a connection. Link to comment Share on other sites More sharing options...
pirx Posted October 31, 2013 Author Report Share Posted October 31, 2013 I think I figured it out. Mavericks now loads the FTDI drivers by default. In order to use libftdi, you need to unload thedriver. Here is what I did: sudo kextunload -v -bundle com.apple.driver.AppleUSBFTDI There may be another way to do this. I haven't tried the serial port yet. Pat Link to comment Share on other sites More sharing options...
tomdehavas Posted December 1, 2014 Report Share Posted December 1, 2014 Hi I had the same problem, "Could not access USB device 0403:6010. If this is linux then use sudo" it was intermittent. Rebooting the computer seemed to help but it would fail after 10 mins or so. I found this forum and twoothers and tried the recommendations to no avail but then found at the end of this forum; http://embeddedprogrammer.blogspot.co.uk/2012/07/hacking-ov7670-camera-module-sccb-cheat.html The conclusion that the cable was the problem. I replaced my cable with a shorter one and it all worked! :-) Link to comment Share on other sites More sharing options...
Jameson Posted October 12, 2015 Report Share Posted October 12, 2015 I've updated my last forum post on how to have the programmer and serial port active simultaneously (http://forum.gadgetfactory.net/index.php?/topic/1148-butterflyloader-on-macosx/?p=17129). This thread looks a bit old so I assume OP may not care anymore, but I'm posting here in the hopes that it'll will help anyone who lands here from google. Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.